COMMON QUESTIONS & ANSWERS
==========================

This file contains answers to some commonly-asked questions.  Please
go through all the sections below when you encounter a problem before
calling Technical Support.

This file contains the following sections:

   1. Installing Windows 3.1 Drivers
      1.1 Setup Windows 3.1 Drivers Again
      1.2 Using DRIVER applet in Control Panel (OEMSETUP.INF)
      1.3 General

   2. DOS drivers
      2.1 Bypass loading of DOS driver

   3. General
      3.1 Eliminating Unwanted Noises
      3.2 Audio Sources Setting
      3.3 Playback Digitized Sound Smoothly
      3.4 Error message appears when WINSETUP.EXE runs


1. INSTALLING WINDOWS 3.1 DRIVERS

   1.1 SETUP WINDOWS 3.1 DRIVERS AGAIN

   Q1. How can I setup my Windows 3.1 drivers again?

   A1. You may setup Windows 3.1 drivers again by running INSTALL from
       your audio directory at the DOS prompt.  Select "Setup Windows" 
       and follow the instructions on the screen to complete the setup.

   1.2 USING DRIVER APPLET IN CONTROL PANEL (OEMSETUP.INF)

   Q1. My drivers are not installed when I use the driver applet in
       Control Panel to add the drivers.  What do I do?

   A1. Before you choose to add any audio drivers, you should first 
       remove all the existing audio drivers shown in the "Installed 
       Drivers List" and then restart Windows. Chances are existing 
       versions of audio  drivers  are installed  when you start-up 
       Windows and  cannot be over-written. You  must also restart 
       Windows after adding all the drivers for these new drivers to 
       take effect.  Refer to your Windows User Reference Manual for 
       more detail on the Driver applet.


   1.3 GENERAL

   Q1. No matter what I try, I can't get sound in Windows.  What
       should I do to fix it?

   A1. Here are some points you  can check:

   a. If you installed Windows 3.1 using the "Express Installation",
      Windows scanned your hard  disk for programs to be installed.
      As a result, older versions of the audio applications may have 
      been installed if they were on your hard disk at the time of 
      installation.  Please remove these icons.  To do this, click 
      on the icon once to select it, then press the delete key. 
      Windows will ask you for confirmation.  Repeat the above
      procedure for each icon.

   b. Open the Driver applet in Control panel.  You should at least
      have the following driver names in the Installed Drivers list:

        Voyetra / Sound Blaster SuperSAPI FM Driver
        Creative Sound Blaster 16 Auxiliary Audio
        Creative Sound Blaster 16 Wave and MIDI
        MIDI Mapper
        Timer
        [MCI] CD Audio    ;this is only for owners of CD-ROM drives
        [MCI] MIDI Sequencer
        [MCI] Sound

      If one or more of the drivers do not exist, you must install the
      driver(s) using the Driver applet in Control Panel (See your
      Windows manual for more details).

   c. Check your SYSTEM.INI by choosing RUN from the File menu of the
      Program Manager and typing NOTEPAD SYSTEM.INI in the command
      line box.  Examine the [drivers] and [sndblst.drv] sections.
      They should look something like this:

        [drivers]
        Timer=timer.drv
        Midimapper=midimap.drv
        Aux=sb16aux.drv
        MIDI=sb16fm.drv
        Wave=sb16snd.drv
        MIDI1=sb16snd.drv

        [sndblst.drv]
        port=220
        int=5
        dmachannel=1
        hdmachannel=5
        MIDIport=330

   d. If Windows refuses to install a device driver or if you get the
      error message "Device not found" when playing a Wave or MIDI
      file, or a CD, be sure that you have the following settings in
      the [mci] section of SYSTEM.INI.

        [mci]
        WaveAudio=mciwave.drv
        Sequencer=mciseq.drv
        CDAudio=mcicda.drv; this is only for owners of CD-ROM drives

      If one or more of the drivers do not exist, you must install the
      driver(s) using the Driver applet in Control Panel (See your
      Windows manual for instructions).  Do not type in the entries
      into the SYSTEM.INI because the files have to be expanded and
      installed into your SYSTEM directory by Windows.


2. DOS DRIVERS

   2.1 BYPASS LOADING OF DOS DRIVER

   Q1. I do not wish to load the DOS drivers VIBRA16.SYS and
       CTMMSYS.SYS at system startup.  What should I do?

   A1. To bypass the loading of the DOS drivers VIBRA16.SYS and
       CTMMSYS.SYS, press the ALT key during system starts up.

       Or, you can use a text editor to REM the following lines in
       your CONFIG.SYS file.  These lines load the DOS drivers at
       system startup.

        DEVICE=C:\SB16\DRV\VIBRA16.SYS /UNIT=0 /BLASTER=A:220 I:5 D:1 H:5
        DEVICE=C:\SB16\DRV\CTMMSYS.SYS


   2.2 LOADING THE DOS DRIVERS

   Q1. I would like load the DOS drivers everytime at system startup,
       What should I do to put the entries in my CONFIG.SYS file?

   A1. Run the program DIAGNOSE in your audio directory with a /A
       parameter.  To do that:

       1) Change to your audio directory.
       2) Type "DIAGNOSE /A" and press Enter.


3. GENERAL

   3.1 ELIMINATING UNWANTED NOISES

   Q1. When I record in either Windows or DOS, it hisses a lot.  What
       can I do?

   A1. Using the mixer, adjust the recording volume for your input
       source to the optimal level.  Bringing the record level close
       to maximum will help to produce noise-free recordings.  Also,
       set the record level for other input sources to zero.  This
       ensures that the only recording is from sources that you want
       to record.

   3.2 AUDIO SOURCE SETTINGS

   Q1. I can't hear anything from the speakers, but when I run the
       diagnostic program, it sounds okay.  What do I do?

   A1. Check the mixer settings for the various sources.  Use the
       programs MIXERSET.EXE in DOS or WMIXER16.EXE in Windows to 
       adjust the settings to a higher level.


   3.3 ELIMINATING JERKY DIGITIZED SOUND PLAYBACK 

   Q1. The playback sounds jerky.  Is my card defective?

   A1. If you are in Windows, this may be due to your choice of
       Windows swap file.  Temporary swap file tends to be fragmented
       causing jerky playback.  If possible, use a permanent swap file
       to eliminate this problem.  Refer to your Windows manual for
       instructions on creating a permanent swap file.

       Loading a disk cache program such as SMARTDRV will also
       eliminate this problem.  To load SMARTDRV, refer to your DOS or
       Windows manual for instructions.

   3.4 Error Message Appears When WINSETUP.EXE Runs

   Q1. When I start Windows and WINSETUP runs, it gives me a dialog
       box saying it can't find the environment.

   A1. The BLASTER environment is not set or is incorrectly set.  This
       program requires that your BLASTER environment is set correctly
       and tallies with your card.  You can type "SET" at DOS prompt
       to check the environment settings.  To ensure that it tallies
       with your audio hardware, run the program DIAGNOSE.EXE from your 
       audio software directory.


                 *********  End of CQA.TXT  *********
