miro.plus high-speed drivers - install disk
for Windows NT (tm) Version 3.1 (final) operating system
Version 1.00                                                       07-Jul-94

miro Computer Products AG
Carl-Miele-Str. 4, D-38112 Braunschweig
Postfach 3452, D-38024 Braunschweig
Phone (+49) (0)531 / 2113-0
Telefax (+49) (0)531 / 2113-99                               
Hotline (+49) (0)531 / 2113-666


Windows NT is a trademark of Microsoft Corporation

1.) Contents of the disk
2.) Supported boards and colour modes
3.) Installation of the drivers
4.) Change of resolutions and colour modes
5.) Special hints concerning the truecolor driver
6.) Association of the drivers with the various boards
7.) Delete drivers
8.) Supported resolutions and frequencies of the various boards
9.) Special hints for miroCRYSTAL/miroMAGIC 20SV/40SV twin/ergo
    and miroCRYSTAL 20SD twin
10.) If problems occur...


1.) Contents of the disk    
    - README.TXT        : Hints (this file)
    - LIESMICH.TXT      : Hints in German    
    - OEMSETUP.INF      : Installation script for SETUP program
    - MIRO110.          : File for disk identification
    - CRYSTAL.SYS       : Miniport-(kernel)-driver
    - FCRYSTAL.SYS      :             "-"
    - S3.SYS            :             "-"
    - CRYSTAL.DLL       : Display-(Win32)-driver
    - FCRYSTAL.DLL      :             "-"
    - S3.DLL            :             "-"


2.) Supported boards and colour modes

    - miroCRYSTAL 20SD      : 8 Bit (256 colours)
    - miroCRYSTAL 20SV      : 8 Bit (256 colours)
    - miroCRYSTAL 40SV      : 8 Bit (256 colours)
    - miroCRYSTAL 10SD      : 8 Bit (256 colours) 
    - miroMAGIC 20SV ergo   : 8 Bit (256 colours) 
    - miroMAGIC 40SV ergo   : 8 Bit (256 colours) 
    - miroMAGIC 20SV twin   : 8 Bit (256 colours) 
    - miroMAGIC 40SV twin   : 8 Bit (256 colours) 
    - miroCRYSTAL 20SV ergo : 8 Bit (256 colours) 
    - miroCRYSTAL 40SV ergo : 8 Bit (256 colours) 
    - miroCRYSTAL 20SV twin : 8 Bit (256 colours) 
    - miroCRYSTAL 40SV twin : 8 Bit (256 colours) 
    - miroCRYSTAL 20SD twin : 8 Bit (256 colours) 

    - miroCRYSTAL 20SD      : 16 Bit (65k colours) 
    - miroCRYSTAL 20SV      : 16 Bit (65k colours) 
    - miroCRYSTAL 40SV      : 16 Bit (65k colours)
    - miroMAGIC 20SV ergo   : 16 Bit (65k colours)
    - miroMAGIC 40SV ergo   : 16 Bit (65k colours)
    - miroMAGIC 20SV twin   : 16 Bit (65k colours)
    - miroMAGIC 40SV twin   : 16 Bit (65k colours)
    - miroCRYSTAL 20SV ergo : 16 Bit (65k colours)
    - miroCRYSTAL 40SV ergo : 16 Bit (65k colours)
    - miroCRYSTAL 20SV twin : 16 Bit (65k colours)
    - miroCRYSTAL 40SV twin : 16 Bit (65k colours)
    - miroCRYSTAL 20SD twin : 16 Bit (65k colours)

    - miroCRYSTAL 20SD      : 32 Bit (16.7M colours) 
    - miroCRYSTAL 20SV      : 32 Bit (16.7M colours) 
    - miroCRYSTAL 40SV      : 32 Bit (16,7M colours)
    - miroMAGIC 20SV ergo   : 32 Bit (16,7M colours)
    - miroMAGIC 40SV ergo   : 32 Bit (16,7M colours)
    - miroMAGIC 20SV twin   : 32 Bit (16,7M colours)
    - miroMAGIC 40SV twin   : 32 Bit (16,7M colours)
    - miroCRYSTAL 20SV ergo : 32 Bit (16,7M colours)
    - miroCRYSTAL 40SV ergo : 32 Bit (16,7M colours)
    - miroCRYSTAL 20SV twin : 32 Bit (16,7M colours)
    - miroCRYSTAL 40SV twin : 32 Bit (16,7M colours)
    - miroCRYSTAL 20SD twin : 32 Bit (16,7M colours)


3.) Installation of the drivers

    a) Start the "Windows NT setup"-program of the group "main" and
       wait a moment.
    b) Open the menu "options" und select "Change System Settings".
    c) Open the option box for "Displays" of the new window 
       "Change System Settings".
    d) In here scroll until the end and select "Others (Requires a 
       disk from a hardware manufacturer)".
    e) A new window "Insert Disk" appears and you are requested to
       insert the installation disk "A:\". If necessary, the default 
       selection can be overwritten.
    f) The window "Select OEM Option" appears and you get a list of 
       the supported miro boards with their resolutions and frequencies.
       Select an appropriate resolution according to your board and monitor 
       and wait a moment.
    g) The window "Change System Settings" appears again, indicating 
       the selected driver at "Displays". Confirm by using the "Close" 
       button.
    h) If you already installed the drivers in former times you are asked
       whether you want to install the former or the new drivers. Confirm 
       the new installation by using the button "New".
    i) A new window "Windows NT Setup" appears and you are requested to  
       insert the installation disk. Confirm by using the "Continue" button.
    j) Now you see the introduction menu of the setup-program. Leave  
       the program now, e.g. by selecting the menu "Options" and "Exit".
    k) Windows NT gives you the information that the new driver will 
       only be effected after a system reboot.

    In case of a board with two drivers available (e.g. 256 and 16.7 
    million colours) the procedure b) to i) has to be repeated for 
    the second driver.

    If problems of the display driver occur when rebooting the system,  
    you have the possibility to reselect the former configuration by 
    using the option "last known good menu". If this doesn`t solve the 
    problem you have to repair your system by using the Windows-NT-setup-
    disk/-CD and the "Emergency Repair Disk". The "Emergency Repair Disk" 
    should include a configuration with a VGA-driver "640x480, 16 colors" 
    and your system has to run properly with this driver under all circum-
    stances. So you can start trouble-shooting now. In order to repair 
    your system only select the options "Inspect configuration registry" 
    and "SYSTEM (System Configuration)".

    If you change the graphics board don`t forget to reconfigure your 
    system on the VGA-driver before. So you get a properly running 
    system after changing the board and you will be able to install 
    the drivers for the new board. 

    The S3-drivers on the Windows NT-Setup-CD don't run together with 
    miroCRYSTAL 20SD (twin), miroCRYSTAL 20SV (ergo/twin), miroCRYSTAL 40SV 
    (ergo/twin) and miroMAGIC 20SV/40SV ergo/twin.


4.) Change of resolutions and colour modes 

    a) Start the "Windows NT setup"-program of the group "main" and
       wait a moment.
    b) Open the menu "options" und select "Change System Settings". 
    c) Open the option box for "Displays" of the new window 
       "Change System Settings". 
    d) Select the desired resolution from the list of the drivers installed 
       for your board and your monitor. Miro now inserts the version number 
       into the description string. Select the desired resolution for your 
       board and monitor with the highest version number to avoid the 
       installation of an old old driver or the use of an old installation
       script. 
    e) If the driver is not installed yet a new window "Windows NT Setup" 
       appears and you will be requested to insert the installation disk. 
       Confirm by using the "Continue"-button. 
    f) If the driver has already been installed you will be asked whether 
       you want to install the current or a new driver. Confirm the use 
       of the pre-installed driver by using the "Current"-button.
    g) Now you see the introduction menu of the setup-program again.  
       Leave the program now ( e.g. by using the menu "Options" and "Exit").  
    h) Windows NT gives you the information that the new driver will only 
       be effected after a system reboot. 


5.) Special hints concerning the truecolor driver 

    The truecolor-driver is created as an accelerated framebufferdriver 
    in the flatmodel. 

    As a basic address of the framebuffer the driver presets the 
    following 32-bit addresses:
    - board for VL-bus    : FE80.0000 (hex)
    - board for PCI-bus   : FE80.0000 (hex)
    If the boards don't run with these addresses (e.g. as a result of an 
    incomplete address decoding of your motherboard) the addresses can be 
    overwritten by an entry into the registry. Repair your system by 
    applicating the measurements described at 3) together with the VGA-
    driver. Start the registry-editor REGEDT32.EXE of the \WINNT\SYSTEM32 
    directory. Use its help-function for operating. Look for the key 
 
  
    HKEY_LOCAL_MACHINE on Local Machine
       \SYSTEM
          \CurrentControlSet
             \Services
                \miroFlatModel
                   \Device0
    Select EDIT and AddValue with your mouse. Insert the ValueName
    "FrameBufferBaseAddress" and the DataType "REG_DWORD". In the following 
    menu-box insert a new address that will shurely work on your computer.   
    After the confirmaton you will find the new inserted address beside 
    data e.g. concerning resolution and colour-mode in the right window. 

    You can delete this value by indicating with the mouse and pressing 
    the DEL-Key. Take care not to change or delete any other value - 
    your system would not be able to run after a system-reboot!  

    One of the following versions of the installation disk will include a  
    DOS-test-program that enables you to check a miro-board concerning 
    available addresses.


6.) Association of the drivers with the various boards 

    - CRYSTAL.SYS and CRYSTAL.DLL   : 256 colours driver for
                                      - miroCRYSTAL 20SD (twin)
                                      - miroCRYSTAL 20SV (ergo/twin)
                                      - miroCRYSTAL 40SV (ergo/twin)
                                      - miroMAGIC 20SV/40SV ergo/twin
    - FCRYSTAL.SYS and FCRYSTAL.DLL : Highcolor- and Truecolor-driver for
                                      - miroCRYSTAL 20SD (twin)
                                      - miroCRYSTAL 20SV (ergo/twin)
                                      - miroCRYSTAL 40SV (ergo/twin)
                                      - miroMAGIC 20SV/40SV ergo/twin
     - S3.SYS and S3.DLL            : 256 colours driver for
                                      - miroCRYSTAL 10SD

    
7.) Delete drivers 

    Drivers that will no longer be used or that are out of date can be 
    removed by reconfiguring with the Windows NT setup-program a different 
    driver (e.g.: VGA Standard 640x480, 16 colors), rebooting the system 
    and then deleting with the help of the file-manager at \WINNT\SYSTEM32 
    the display-driver (extension: .DLL) and at \WINNT\SYSTEM32\DRIVERS 
    the miniport-driver (extension: .SYS). From now on miro adds the 
    file-time to the version number.

    After the installation of drivers with the option "Other..." there 
    will exist several files OEMVIOx.INF (x=0,1,...) in the directory  
    \WINNT\SYSTEM32. These are the renamed installation scripts of the  
    current and the former installation disks. You should delete all of 
    them except the file with the highest 'x' (the current installation). 
    If you don't do so, drivers will be listed several times and by 
    different installation disks and versions.

    Moreover the refering key should be deleted in the registry with the 
    help of the registry-editor REGEDT32 (look at 4.) ). Look for the key 
    HKEY_LOCAL_MACHINE on Local Machine
       \SYSTEM
          \CurrentControlSet
             \Services
                \miro8BPP               for the 256 colours driver
                \miroFlatModel          for the highcolor- / truecolor-driver
                \s3                     for the driver for 10SD
    Select the key in the left window with your mouse and delete it with 
    the DEL-key. Take care not to change or delete any other key - your 
    system would not be able to run after a system-reboot!  


8.) Supported resolutions and frequencies of the various boards 

    With this disk-release miro changes the original timings of these
    drivers to timings that are approximated to the VESA-standards. 
    Horizontal and vertical refresh rates are approximated data and 
    may change according to the technical and market development. 
    The timings for resolutions of 1408x1024 pixels are not part of 
    the VESA-standards but are adapted to them by miro.

    - miroCRYSTAL 40SV (ergo/twin), miroMAGIC 40SV ergo/twin
       640 x  480: 31,5kHz/60Hz 37,5kHz/75Hz (256, 65k, 16,7M colours)   
       800 x  600: 38kHz/60Hz   47kHz/75Hz   (256, 65k, 16,7M colours)    
      1024 x  768: 48,5kHz/60Hz 60kHz/75Hz   (256, 65k, 16,7M colours)   
      1280 x 1024: 64kHz/60Hz   80kHz/75Hz   (256, 65k colours)   
      1408 x 1024: 66kHz/60Hz   74kHz/70Hz   (256, 65k colours)    

    - miroCRYSTAL 20SV (ergo/twin), miroMAGIC 20SV ergo/twin
       640 x  480: 31,5kHz/60Hz 37,5kHz/75Hz (256, 65k, 16,7M colours)   
       800 x  600: 38kHz/60Hz   47kHz/75Hz   (256, 65k, 16,7M colours)    
      1024 x  768: 48,5kHz/60Hz 60kHz/75Hz   (256, 65k colours)   
      1280 x 1024: 64kHz/60Hz   80kHz/75Hz   (256 colours)   
      1408 x 1024: 66kHz/60Hz   74kHz/70Hz   (256 colours)    

    - miroCRYSTAL 20SD (twin)
       640 x  480: 31,5kHz/60Hz 37,5kHz/75Hz (256, 65k, 16,7M colours)   
       800 x  600: 38kHz/60Hz   47kHz/75Hz   (256, 65k, 16,7M colours)    
      1024 x  768: 48,5kHz/60Hz 60kHz/75Hz   (256, 65k colours)   
      1280 x 1024: 64kHz/60Hz   80kHz/75Hz   (256 colours)   

    - miroCRYSTAL 10SD
       640 x  480: 31,5kHz/60Hz 38kHz/72Hz                         (256 colours)   
       800 x  600: 38kHz/60Hz   48kHz/72Hz                         (256 colours)    
      1024 x  768: 48kHz/60Hz   56kHz/70Hz 60kHz/75Hz              (256 colours)   
      1280 x 1024: 64kHz/60Hz   78kHz/72Hz 48kHz/87Hz-interlaced   (256 colours)   
      1280x1024 with 256 colours with a miroCRYSTAL 10SD can only be effected 
      with a RAM upgrade to 2MB


9.) Special hints for miroCRYSTAL/miroMAGIC 20SV/40SV twin/ergo
    and miroCRYSTAL 20SD twin

    If you want to install/configure the graphics board 
    "miroCRYSTAL 40SV ergo/twin" resp. "miroMAGIC 40SV ergo/twin" 
    please select "miroCRYSTAL 40SV" in the setup-program.

    If you want to install/configure the graphics board 
    "miroCRYSTAL 20SV ergo/twin" resp. "miroMAGIC 20SV ergo/twin" 
    please select "miroCRYSTAL 20SV" in the setup-program.

    If you want to install/configure the graphics board 
    "miroCRYSTAL 20SD twin" please select "miroCRYSTAL 20SD" in the 
    setup-program.

    This version of drivers do not support the "TWINFACE" 
    mode of the miroCRYSTAL 20SV/40SV twin. However, the output is 
    switched to the second HiRes board and -monitor. Despite the 
    VGA DOS box is displayed in full screen mode on the first monitor.
    

10.) If problems occur... 

    In case of problems with the VGA-DOS-box in fullscreen-mode you 
    should ask your dealer or miro for an update of the BIOS-ROM. 
    A unsyncroniced image may be caught by switching between the
    windowed- and the fullscreen-mode of the VGA-DOS-box.

    The VGA-DOS-box as a part of the operating system only supports 
    the resolutions available for a 'standard VGA', e.g. display 
    modes up to 320x200 pixels with 256 colors or 640x480 pixels with 
    16 colors. If a DOS application tries to use a higher resolution, 
    the VGA-DOS-box, or, in the worst case, the hole system might crash.
