                                                               Dec. 1995

                          ETHER PCI Ethernet Card
                 Windows for Workgroups V3.11 Driver programs
                 ============================================

**************************
*  Hardware Requirement  *
**************************

  The ETHER PCI Series Ethernet Card include below adapters *
  . ETHER ETHER-PCI PCI Ethernet adapter(Support 10M PCI)
  . ETHER ETHER-PCI-D PCI Ethernet adapter(support 10M PCI and BOOTROM function)
  . ETHER ETHER-100TX PCI Fast Ethernet adapter(support 10/100 PCI)


**********************************************************
*  README for Windows for Workgroups V3.11 Installation  *
**********************************************************

The Ethernet LAN drivers for Windows for Workgroups 3.11
contained in this diskette are as follows:

\WFW311\ETHPCI.386    ETHER NDIS 3.0 driver for Windows for Workgroups 3.11
\WFW311\OEMSETUP.INF  OEMSETUP file for Windows for Workgroups
\DISK1

Installation Procedure:

(1)  When LAN drivers is installed, Windows for Workgroups will present a list
     of all available drivers.  Since there will be no drivers initially,
     select UNLIST for 3rd party adapters not in the driver list.

(2)  Windows for Workgroups will ask for the drive/path containing the
     Windows for Workgroups drivers.  Insert the ETHER driver diskette in
     drive A: and respond with the following

     A:\WFW311

(3)  Windows for Workgroups will attempt to locate an OEMSETUP.INF file in the
     specified path. If you have entered the path name correctly, Windows
     for Workgroups should copy the appropriate drivers to the Windows for
     Workgroups system.

(4)  At this point, the driver would have been properly copied and the
     installation would proceed to the next step.  Please refer to your
     Windows for Workgroups installation guide for correct procedures.

(5)  After the initial installation, the drivers will be permanently
     copied to the Windows for Workgroups system.
     Subsequent network driver lists will already contain ETHER PCI drivers.

*****************************************************************
*   How to Install driver on MS Windows for Workgroups 3.11  *
*****************************************************************

Inside Windows, please select the following icons:  Windows Setup =>
Options => Change Network Settings.. =>  Drivers  =>  Add Adapter  =>

   1) When asked for the name of network card, select "Unlisted Network Card"
   2) Insert the release Driver Disk in drive 'A'
   3) When asked for the path of VENDOR-PROVIDED driver file, type A:\WFW311
   4) Select the "ETHER PCI Ethernet Adapter" (example)
   5) You don't need to specify the IRQ and I/O settings, since they are
      auto-selected by your PC BIOS.

After WFW finishes the setup for PCI adapter, it will create the following files:

\CONFIG.SYS
===========
:
device=c:\windows\ifshlp.sys

\AUTOEXEC.BAT
=============
c:\windows\net start


\WINDOWS\PROTOCOL.INI
=====================
[network.setup]
version=0x3110
netcard=ETH$PCI,1,ETH$PCI,3
transport=ms$nwlinknb,NWLINK
transport=ms$ndishlp,MS$NDISHLP
transport=ms$netbeui,NETBEUI
lana0=ETH$PCI,1,ms$netbeui
lana1=ETH$PCI,1,ms$nwlinknb
lana2=ETH$PCI,1,ms$ndishlp


[protman]
DriverName=PROTMAN$
PRIORITY=MS$NDISHLP

[ETH$PCI]
DriverName=ETHPCI$
AdapterCFID=00021011
AdapterType=5
BusType=5
MediaType=1
BurstLength=10
ConnectionType=0
PciMechanism=0
NetworkAddress=000000000000
ReceiveBuffers=10

[ETHPCI]
Adapters=ETH$PCI

[NWLINK]

BINDINGS=ETH$PCI
[MS$NDISHLP]
DriverName=ndishlp$
BINDINGS=ETH$PCI

[NETBEUI]
DriverName=netbeui$
SESSIONS=10
NCBS=12
BINDINGS=ETH$PCI
LANABASE=0



